Start with the Kraken's role on the vehicle
The RigWheels Kraken Camera Car Mount is a mounting and positioning system for cameras on vehicles, designed for intuitive installation and movement shots. It uses a hinge design and standard tripod heads, so the setup question is less about assembling a puzzle and more about planning where the mount goes, how the camera is supported, and how you confirm the suction is holding.
The supplied catalog describes a complete kit rather than a bare suction cup: a main suction cup with a low-suction audible alarm, 75 mm half-bowl mounts, additional adapters, and a Pelican case for transport. Those pieces shape the installation sequence below.
What the Kraken kit includes for installation
- RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur): Hinge design for easy, quick and secure installation The hinge is the core of the mounting action; plan the camera position around it rather than forcing the cup into an awkward angle.

RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur) - RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur): 75 mm half-bowl mount included for direct camera mounting This is the interface that connects a compatible camera or head to the mount; check your camera base and head before the shoot day.
- RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur): Low-suction audible alarm on the main suction cup The alarm is a safety signal during installation and while shooting; treat any alarm as a reason to stop and recheck the cup.
- RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur): Capacity up to 79 kg The stated load capacity is high, but it is a limit, not a target; keep the camera, head and adapters within it and verify the vehicle surface separately.
- RigWheels Kraken Camera Car Mount – Support Voiture pour Caméra Cinéma (Kit Loueur): Pelican case included for transport Keeping the kit in its case protects the cup, bowls and adapters between locations, which matters when the mount travels to different vehicles.
A practical Kraken installation sequence
The supplied information confirms the hinge, the 75 mm half-bowl, the suction alarm and the 79 kg capacity, but it does not list a formal tightening torque, cup-placement distance or surface-preparation procedure. Use the sequence below as a planning framework and follow any instructions that come with the kit for the details not covered here.
- 1. Inspect the vehicle surface before mounting: Choose a clean, flat area that can accept the main suction cup. The catalog does not specify approved surface types, so avoid damaged, porous or flexible panels unless the manufacturer's own instructions confirm them.
- 2. Set up the hinge and bowl before attaching the camera: The hinge design is intended for quick, secure installation. Position the mount so the hinge can move through its range without the camera striking the vehicle, then fit the 75 mm half-bowl for direct camera mounting or your standard tripod head.
- 3. Attach the camera and check the load: Add the camera, head and adapters, then confirm the total is within the stated 79 kg capacity. The catalog does not give a separate safety margin, so keep the load well inside the limit and recheck after any change.
- 4. Confirm the suction alarm is quiet: The low-suction audible alarm on the main cup is your in-use warning. If it sounds, stop, reseat the cup and recheck before continuing; do not treat the alarm as a nuisance to ignore.
- 5. Make a slow test pass before the real shot: The catalog describes highway-speed and race-film use, but it does not give a speed limit or a test procedure. Start slowly, watch the mount and alarm, and only increase speed once you are satisfied the installation is stable.
Suction mount safety checks that matter on a moving vehicle
The Kraken's alarm and high capacity help, but they do not replace a pre-shot check. These checks follow directly from the supplied features.
- Listen for the low-suction alarm: The alarm is on the main suction cup. Assign someone to monitor it during the shot, especially when engine or road noise could mask it.
- Keep the camera and head within the 79 kg capacity: Weigh or estimate the full payload, including the head and adapters, before mounting. The capacity figure is the catalog's stated limit.
- Use standard tripod heads as intended: The Kraken is described as compatible with multiple tripod head types and adapters. Confirm your specific head fits the 75 mm half-bowl or supplied adapters before the shoot.
- Reposition with the hinge, not by levering the cup: The hinge is designed for quick installation and repositioning. Use it to change the camera angle rather than pulling on the suction cup.
Transport and repositioning between shots
The Pelican case is part of the kit, which makes the Kraken practical for productions that move between vehicles or locations. Pack the cup, 75 mm half-bowl and adapters back into the case when the mount is not in use; this protects the sealing surfaces and keeps the alarm and hinge from being knocked in transit.
For multi-angle work, the catalog describes fixing several cameras at different points on the vehicle. That is a planning decision: each mount needs its own surface check, load check and alarm check, and the total number of mounts is limited by the vehicle and the kit you have, not by a catalog figure.
What the supplied information does not confirm
The catalog does not provide a formal step-by-step installation procedure, tightening torque, approved surface list, speed limit or maintenance schedule for the Kraken. It also does not confirm compatibility with specific camera models beyond the 75 mm half-bowl and standard tripod head description. Treat those as questions for the manufacturer or your rental house before the shoot, and do not infer them from the capacity or alarm features.


