What the Wooden Camera LWS Handgrip Kit 15mm is for
The Wooden Camera LWS Handgrip Kit 15mm (A01000) is a complete handgrip set for shoulder-mounted camera configurations. It is built around a 15mm LWS Crossbar with pivoting 32mm rosettes, two extensions, two Rosette Handgrips, and a pack of color rings. The kit is made from 7075 aluminum, and the handgrips are ODI BMX-style grips in TPE material.
The intended use is documentary or fiction shooting where you need a light, stable, customizable shoulder setup. The crossbar design lets you leave it mounted on 15mm LWS rods even when the camera is on a standard ARRI dovetail, so you can move between tripod and shoulder work without a full teardown.
Kit contents that drive the setup
- Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: The kit includes a 15mm LWS Crossbar, two extensions, two Rosette Handgrips, and a pack of color rings. These are the parts you will assemble; confirm each is present before mounting.

Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées - Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: The 15mm LWS Crossbar has pivoting 32mm rosettes for adjusting arm position. Rosette pivots set the handgrip angle and reach, so plan to adjust them after the crossbar is on the rods.
- Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: The 32mm rosettes use standard M6 screws, and 1/4”-20 and 3/8”-16 threads are available for accessories such as monitors. You can attach a monitor or other accessories directly to the rosette area without extra clamps.
A practical installation sequence
The supplied information describes the kit's parts and adjustment points but does not include a step-by-step factory procedure. The sequence below is a conservative assembly order based on those parts and their stated functions. Check each connection by hand before adding camera weight.
- Mount the crossbar on your 15mm LWS rods: The crossbar is designed to stay on 15mm LWS rods even when the camera is installed on a standard ARRI dovetail. Fit it to your rod system first so the rest of the kit hangs from a stable base.
- Attach the extensions to the rosettes: The crossbar's pivoting 32mm rosettes accept the arms. The extensions are pentagonal and ultralight, and each has an offset to help the kit fold.
- Fit the Rosette Handgrips: The ODI BMX-style handgrips are TPE and shaped for comfort over long shoots. Attach them to the extensions and check that each grip is secure before loading.
- Set the rosette angle and tighten with M6 screws: Use the standard M6 screws at the 32mm rosettes to lock the arm position. Adjust both sides so the grips sit where your hands naturally fall.
- Add accessories to the 1/4”-20 or 3/8”-16 threads: The rosette area provides these threads for monitors and similar accessories. Confirm the accessory's mounting thread matches before attaching.
- Install the color rings: The included pack of 8 color rings lets you identify cameras or configurations quickly. Fit them after the grips are in place.
Adjusting the handgrips for shoulder work
The 32mm rosettes are the main adjustment point. Because they pivot, you can change the angle of the arms without removing the crossbar from the rods. Set the angle with the camera on your shoulder so the grips land where your hands rest, then tighten the M6 screws.
The extensions have a built-in offset that helps the kit fold. That folding behavior is useful for transport, but the supplied information does not specify a load rating or a maximum extension length. Keep the arms in a comfortable position and avoid overextending them beyond what feels stable with your camera weight.
Fastener details worth knowing
Each button on the kit is stainless steel with a DLC coating for added resistance, and it has a central hole that accepts a 3/16” or 4mm hex key. That means you can tighten or adjust the buttons with a common hex tool rather than a proprietary one.
The M6 screws at the rosettes are standard, so replacement or adjustment is straightforward if you already have M6 hardware. The 1/4”-20 and 3/8”-16 threads are the common accessory sizes, which covers many monitors and small receivers.
Build and handling evidence
- Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: The kit is made from 7075 aluminum, and the extensions are ultralight with a pentagonal shape. This supports the kit's stated aim of a light but solid shoulder configuration.
- Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: The handgrips are ODI BMX-style grips in TPE material. Grip material and shape affect comfort during long handheld shoots.
- Wooden Camera LWS Handgrip Kit 15mm (A01000) – Kit Poignées: Each button is stainless steel with a DLC coating and a central hole for a 3/16” or 4mm hex key. You can adjust the buttons with a standard hex key instead of a special tool.
What to check before you shoot
Before mounting the camera, confirm the crossbar is seated on the 15mm LWS rods and that the rosette screws are tight. With the camera on your shoulder, check that both handgrips are at a comfortable angle and that any monitor or accessory on the 1/4”-20 or 3/8”-16 threads is secure.
The supplied information does not confirm a maximum payload, a specific rod length, or a required torque for the M6 screws. If you are unsure about load capacity for your camera build, check with Wooden Camera or your dealer before relying on the kit in the field.


